Explore our new custom Felt and Twill patch samplesView Patch Samples
Velora Digitizing logoVELORADIGITIZING
Guides8 min read

Embroidery Logo Size Chart: Standard Sizes for Every Placement

Standard embroidery logo sizes for shirts, caps, sleeves, back neck, yoke, jacket backs, aprons, scrubs, totes, towels and beanies in one chart, plus how to choose a size between the ranges.

Velora Digitizing logo
Velora Digitizing Team

Embroidery Digitizing Studio

Polo shirt, cap, apron and jacket with embroidered logos and a tape measure for sizing

Commercial Digitizing Service

Need production-ready machine files? Explore our Custom Embroidery Digitizing

Get Free Quote

The standard embroidery logo size depends on where it goes: about 3.5 inches wide on a shirt chest, about 2.25 inches high on a structured cap front, 2.5-3.5 inches wide on a sleeve, 2-3 inches wide below the back collar, 10-12 inches wide on an adult jacket back, and 6-8 inches wide on a standard tote. The chart below lists every common placement in inches and millimeters, with a link to the detailed guide for each one.

Use the chart as the starting point, then adjust for the garment size, the shape of the logo and the smallest text in it. The final section explains how to choose a size inside each range.

Embroidery logo size chart by placement

Standard embroidery logo sizes by placement (adult garments)
PlacementTypical sizeIn mmDetailed guide
Chest (shirt, polo)3-4 in wide; 3.5 in most common75-100 mmLeft chest placement chart
Full front (center chest)8-11 in wide200-280 mmHow to embroider a shirt
Hoodie center chest6-10 in wide150-255 mmHoodie embroidery guide
Structured cap frontUp to about 2.25 in high x 4.5 in wide57 x 115 mmCap digitizing guide
Low-profile cap frontUp to about 2 in high x 4 in wide50 x 100 mmCap digitizing guide
Cap sideUp to about 1 in high x 2.5 in wide25 x 65 mmCap digitizing guide
Cap back (above strap)About 1 in high x 2.5-3 in wide25 x 65-75 mmCap digitizing guide
Beanie cuffAbout 2-2.25 in high x 3-5 in wide50-57 x 75-125 mmBeanie embroidery guide
Upper sleeve2.5-3.5 in wide65-90 mmSleeve embroidery guide
Back neck / below collar2-3 in wide, up to about 1.5 in tall50-75 mmThis guide, below
Upper back yoke3-10 in wide, 1-3 in tall75-255 mmThis guide, below
Jacket back (adult)10-12 in wide255-305 mmJacket back size guide
Scrub top chest3-4 in wide75-100 mmThis guide, below
Bib apron chest3.5-5 in wide90-125 mmThis guide, below
Tote bag (standard 15 x 16 in)6-8 in wide150-200 mmTote bag embroidery guide
Towel border or corner4-8 in wide100-200 mmTowel and fleece guide
Baby blanket name4-8 in wide100-200 mmBaby blanket guide

Each row links to the guide that owns that placement, with exact marking distances and garment-by-garment adjustments. Sizes above are for adult garments; for youth and ladies' fits, use the lower end of each range or about 10-15% smaller.

Back neck and yoke embroidery sizes

Back neck logos sit just below the collar on the outside of the garment. They are small, usually 2-3 inches wide and no more than about 1-1.5 inches tall, centered about 1 inch below the collar seam. A wider upper-back or yoke design, such as a website, slogan or company name, runs 3-10 inches wide and 1-3 inches tall, starting 2-3 inches below the collar.

  • Keep back neck text short: one word or a short URL.
  • Avoid heavy fills; the area sits on the neck and a stiff patch of stitches is uncomfortable.
  • On tees, use a cutaway stabilizer so the logo does not stretch out of shape across the shoulders.

Scrubs, aprons and workwear sizes

Embroidery sizes for scrubs, aprons and workwear
ItemPlacementTypical sizeNotes
Scrub topChest3-4 in wideName line under the logo, letters at least 0.25 in tall
Scrub topSleeveAbout 2.5 x 1 inShort sleeves leave little room
Lab coatChest above pocket3-4 in wideName and title in 2 lines under it
Bib apronChest3.5-5 in wideCenter on the bib, 2-3 in below the top edge
Bib apronCenter bib7-8 in wideFor a larger brand mark
Waist apronPocket or corner3-4 in wideKeep clear of pocket seams
Work shirtChest or above pocket3-4 in wideName patch goes on the opposite side
Work jacketBack10-12 in wideSimplify fine detail at this size

Scrubs and lightweight workwear are usually thin polyester blends that pucker under dense stitching, so the digitizer should use lighter density and a cutaway stabilizer. See how to fix embroidery puckering for the details.

How to choose a size within the range

  1. 1Start with the smallest text. Capitals need to be at least about 0.25 inch (6 mm) tall. If your smallest line is too small at the chart size, go larger or remove that line.
  2. 2Consider the logo shape. Wide horizontal logos use the full width; round or square logos look right at about 70-85% of the width given for that placement.
  3. 3Match the garment size. Larger adult sizes can take the top of the range; youth, ladies' fit and small items take the bottom.
  4. 4Check the hoop. The design must fit the sewing field of the hoop or cap frame that will be used; see the embroidery hoop sizes chart.
  5. 5Use one size per placement across the order. Mixing sizes on the same placement for different shirt sizes means separate files.

Sizes for youth, ladies' and plus sizes

Adjusting embroidery logo size by garment fit
FitChest logo widthJacket back widthNotes
Youth (XS-L)2.5-3.25 in7-9 inLogo center slightly higher on the chest
Ladies' fit2.75-3.5 in9-10 inNarrower shoulders; keep the logo away from the armhole
Adult S-XL3-4 in10-12 inThe standard ranges in the main chart
Adult 2XL-4XL3.5-4 in11-12 inStay within the hoop; do not exceed the largest frame

For mixed orders, most decorators sew one size across all adult garments and a second, smaller file for youth or ladies' fits. Two files cost less than a logo that looks oversized on small shirts or lost on large ones.

  • The placement and the finished width or height in inches for each version.
  • The garment type and fabric, for example pique polo, structured cap or fleece jacket.
  • Your machine brand or the format you need, such as DST or PES.
  • Thread colors, ideally as Pantone or thread chart numbers.

One logo, several sizes

A logo usually needs a separate file for each placement, because a chest logo, a cap front and a jacket back differ by much more than the 10-20% a finished stitch file can be scaled. The resizing guide explains why. When you order, list every placement and size you need so each version is built for its own size.

Velora digitizes each placement by stitch count: up to 5,000 stitches for $6.99 (Basic), up to 15,000 for $12.99 (Standard), and unlimited stitches with 2-4 hour delivery for $19.99 (Rush). Most chest, cap and sleeve versions fit the Basic or Standard plan. See pricing or order through embroidery digitizing services.

Tagsembroidery logo size chartstandard embroidery logo sizeswhat size should my logo be for embroideryembroidery size chartembroidery placement sizes
Velora Digitizing logo

Written by the Velora Digitizing Team

Digitizing Studio

This guide is written and reviewed by the digitizers at Velora Digitizing, who prepare embroidery files for caps, jackets, patches, and left chest logos every day. The advice here comes from the same stitch-path, underlay, and fabric choices we make on client orders.

Related service

Custom Embroidery Digitizing

EXPLORE SERVICE
FAQ

Questions About This Topic

Quick answers related to this article.

It depends on the placement. The most common sizes are about 3.5 inches wide on a shirt chest, about 2.25 inches high on a structured cap front, 2.5-3.5 inches wide on a sleeve, 10-12 inches wide on an adult jacket back, and 3-4 inches wide on scrubs. The chart in this guide lists every common placement in inches and millimeters.

Still have questions? We're here 24/7.

Contact Our Team

Keep Reading

Ready to Digitize Your Design?

Get your FREE quote now and experience premium quality digitizing.

START YOUR ORDER